This month we present a series of tutorials on Ableton Live 10 to whet your appetite ahead of its imminent release this 2018. As we already mentioned in a previous news item, one of the highlights is the inclusion of new devices. Ramir Martinez, our Certified Trainer at the Microfusa school, introduces you to the basic operation of Wavetable, a powerful wavetable synthesizer with numerous modulation possibilities and a very comprehensive graphical interface that allows us to view all parameters at a glance.
Wavetable | Arpeggiated Lead Design
This wavetable synthesizer is one of the most exciting new features in the new version of Ableton Live 10 and is added to the existing family of instruments. Instead of having a limited number of waveforms, as in the case of Analog or Operator, we find an extensive variety. In this article, we will introduce ourselves to the basic structure of the instrument and carry out an essential design for an arpeggiated Lead.Wavetables and Oscillators
The fundamental difference of Wavetable compared to the rest of the Live synthesizers is that it incorporates a wavetable in its oscillators, that is, a set of waves for the same selected waveform. If we load an instance on a track, we see by default the Basic Shapes table, which shows a graphic viewer showing us four states, from square to sine. A slider located on the right allows you to choose any of the intermediate states.
Intermediate wave chosen for Basic Shapes
One of the most exciting aspects of this synthesizer is the large number of existing tables, grouped into various categories: Basics, Complex, Filter, etc. Some are very interesting from a sound design point of view. In addition, Wavetable has two oscillators and a sub-oscillator to be able to create timbre rich in partials.A setting for a Lead. Tables, detuning, and unison mode.
Leads and Pads are some of the types of presets that can benefit the most from the layering of oscillators. We can create a basic Lead timbre using two wavetables in two oscillators and applying a certain degree of detuning using the Detune control.

Filters
Once the base timbre is built, we can route the signal from the oscillators to the filtering section. In this section, we can process the sum signal of the oscillators (Series and Parallel modes) or also process each oscillator with an independent filter (Split). Each filter can be activated independently and has analog circuitry emulation options (just like in the rest of the Live instruments) to give more character to the filtering through a certain amount of distortion.
Filtering section with two filters working in parallel
Modulators
Wavetable allows you to apply a total of five internal modulators, three envelopes and two LFOs. The main envelope – of the amplifier – is the one that has the greatest effect on the final sound. The envelopes have classic ADSR segments, although each segment allows you to change its curvature, which allows greater control over the parameter being modulated. In addition, the envelopes have various modes. By default, the None mode reproduces the typical behavior associated with an ADSR curve, where the action of the pressed note triggers the ADS segments, while the release of the note triggers the R segment. The Trigger, mode, however, is more suitable for triggering the entire envelope with the mere action of pressing the note, a feature that is common in the programming of percussive timbres. If we want to obtain a punchy, percussive sound, suitable for an arpeggiated Lead, we can use the Trigger mode, modify the segments and obtain an AD curve, as shown in the following figure.
AD envelope over the amplifier
External control
Once the basic adjustments are made, we can model the final sound of the timbre using a few parameters. The Decay time in the envelope and the filter cutoff frequency are the most obvious, since they provide a great change in the timbre and the dynamic evolution of the Lead. A third parameter that produces great changes in the filter is the position of the wavetable. Mapping these controls to the macros of an Instrument Rack that contains Wavetable can allow you to control the manual modulations with an external controller such as Push.
Macros of an Instrument Rack mapped to various Wavetable parameters
Below, a video of the process to follow: [video:https://youtu.be/_mgZdqIuslA align:center] Remember that this Thursday, January 18 we will have a demonstration of this and other production processes taught by our Ableton Certified Trainer, Ramir Martínez. Free entry with registration, limited capacity. Ramir Martinez has been teaching classes at microFusa since 1993 in the areas of Sound, Electronic Music Production and Live Performance, creating the content of these last two areas. As a music producer and sound engineer, he has been behind some of the productions and remixes of some of the most relevant bands in the City of Barcelona in the past decade, such as Facto Delafé and Las Flores Azules, Love Of Lesbian or Mishima, and has been responsible and head of the Tsunami Music label for a decade. His artistic career has adopted various names and dates back to 1995 leading various electronic pop and rock bands among which Groove Crew and Mandalas stand out, and more recently Kulyela, a purely electronic project rooted in breaks, with which he has published more than two dozen works on various labels (Liquid Records, B-Core, Blood Sugar Records, Tsunami Music…) Currently, he is immersed in the Monocrom! project, an experimental jazz and electronic duo.If you need more information about this or other publications from Microfusa, do not hesitate to contact our team, we will be happy to help you. MICROFUSA / BARCELONA STORE Sepúlveda, 134. Barcelona / Tel.: 934 553 695 MICROFUSA / MADRID STORE Ardemans, 9. Madrid / Tel.: 917 242 800 MICROFUSA / ONLINE STORE
